PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF BOE HYDIS AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE HYDIS AND MUST BE RETURNED TO BOE HYDIS UPON ITS REQUEST
TITLE : HX121WX1-100 Preliminary Product Specification Rev. P2
FOR MORE INFORMATION:
AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA, 92656 Http://www.AZDISPLAYS.com
BOE HYDIS TECHNOLOGY
SPEC. NUMBER B2005-C001-A (1/3)
PRODUCT GROUP TFT LCD
REV. P2
ISSUE DATE 2008. 01. 14
PAGE 1 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
REVISION HISTORY
REV. P0 ECN NO. DESCRIPTION OF CHANGES Initial Release -.Add the surface treatment_AR(4page) -.Add the life time test condition (8page) -.Add the color reproduction(9page) -.Change the reflectance(9page) -.Change the Power Consumption, CR, Gamut, Chromaticity, Reflectance DATE `07. 08. 08 PREPARED H. R. Park
P1
'07. 08. 10
H. R. Park
P2
'08. 01. 14
H. R. Park
SPEC. NUMBER B2005-C001-A (2/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 2 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
Contents
No 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 General Description Absolute Maximum Ratings Electrical Specifications Optical Specifications Interface Connections Signal Timing Specifications Signal Timing Waveforms Input Signals, Basic Display Colors & Gray Scale of Colors Power Sequence Mechanical Characteristics Mechanical Drawing Reliability Test Handling & Cautions Labels Packing Information Item Page 4 6 7 9 14 17 17 19 20 21 22 25 25 27 28
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 3 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
1.0 GENERAL DESCRIPTION
1.1 Introduction HX121WX1-100 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 12.1 inch diagonally measured active area with WXGA resolutions (1280 horizontal by 800 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical Stripe and this module can display 262,144 colors. The TFT-LCD panel used for this module is a low reflection and higher color type.
LVDS Input Signal
1 Connector (CN 1 )
Source Driver LVDS Rx + T/CON
VDD
DC/DC Gamma Vcom
TFT LCD Panel BACK LIGHT (Fluorescent Lamp) 1280 x800
Gate Driver
HVDD VDIM
LED Driver
Back Light (SMD LED Array)
CN2
1.2 Features Thin and Light Weight 3.3 V Logic Power Supply 12V Back-light Power Supply 1 Channel LVDS Interface SMD LED (48EA) Array (Bottom Side/Horizontal Direction) 262,144 Colors Data Enable Signal Mode Side Mounting Frame Green Product (RoHS) Anti-Reflection polarizer product for sunlight readability SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 4 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT 1.3 Application Tablet PC (Wide type)
REV P2
ISSUE DATE 2008. 01. 14
1.4 General Specifications
Parameter Active area Number of pixels Pixel pitch Pixel arrangement Display colors Display mode Outline dimension Weight Back-light Surface treatment
Specification 261.12(H) x163.20(V) 1280(H) x800(V) 0.204(H) x0.204(V) RGB Vertical Stripe 262,144 Normally Black 276.80.3(H) x180.00.3(V) x6.8(D:Max.) 265(Typ.) / 275(Max.) SMD LED (48EA) Array Anti-Reflection, 2H
Unit mm pixels mm
Remarks
colors
mm g
Note 1 Note 2
Note 1 : At PCB side (LED Side: 4.6mm Max.) Note 2 : Without digitizer
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 5 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
2.0 ABSOLUTE MAXIMUM RATINGS
The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit.
Ta=25+/-2C
Parameter Logic Power Supply Voltage Logic Power Supply Voltage Back-light Power Supply Voltage Back-light LED Current Back-light LED Reverse Voltage Operating Temperature Storage Temperature
Symbol VDD VIN HVDD ILED VR TOP TSP
Min. -0.3 -0.3 -0.3 0 -20
Max. 4.0 VDD+0.3 40 30 5 +50 +60
Unit V V V mA V
Remarks
Note 1
Note 1, Note 2
Note 1. Ambient temperature vs allowable forward current are shown in the figure below. Note 2. Temperature and relative humidity range are shown in the figure below. 90% RH Max. ( 40 Ta) Maximum wet - bulb temperature at 39 or less. ( > 40) No condensation.
Relative Humudity
100 90 80 (40, 90)
60
Operating Range
(50, 50)
40 (60, 27) 20 5 -40 -20 0 20 40 60 80
Storage Range
Temperature ()
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 6 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
3.0 ELECTRICAL SPECIFICATIONS
3.1 Electrical Specifications < Table 3. Electrical Specifications > Parameter
Logic Power Supply Voltage Logic Power Supply Current Back-light Power Supply Voltage Back-light Power Supply Current Back-light Power Consumption LED Driver's Efficiency Back-light PWM Frequency High Level PWM Signal Voltage Low Level PWM Signal Voltage High Level Differential Input Signal Voltage Low Level Differential Input Signal Voltage Back-light LED Voltage / Back-light LED Total Voltage Back-light LED Current / Back-light LED Total Current Life Time PD EBL (Extended Battery Life) PLED Ptotal PD Power Consumption PLED Ptotal VDD IDD HVDD IHVDD PBL FPWM VPWMH VPWML VIH VIL VLED /VBL ILED /IBL
Min.
3.0 7.0 200 2.1 -100 10,000
Typ.
3.3 364 12.0 255 3.06 82 280 3.3 0 3.1 / 37.2 16.9 / 67.6 0.95 0.50 1.45 1.0 2.51 3.51
Max.
3.6 TBD 20 305 3.66 350 5.0 0.6 +100 3.5/ 42.0 17.8/7 1.2 TBD 0.88 TBD TBD 2.99 TBD
Unit
V mA V mA W % V V mV mV V mA Hrs
Remarks
Note 1 Note 1 Note 2 Note 2, 3 Note 2, 3 Note 2, 3
VCM = 1.2V
Note 4 Note 4 Note 6
Note 1, 2, 3
W W W
Note 1 Note 4 Note 1, 4
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 7 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for 3.3V at 25. a) Typ : Window XP pattern, b) Max : Vertical Sub line pattern c) EBL : Mosaic pattern ( 32 X 32 ) 2. The power supply voltage and current is measured and specified at the interface connector of LCM including LED Driver. 3. Reference value, which is measured with LED Driver for 12V. 4. Reference value, which is measured without LED Driver. 5. Calculated value for reference (VLED x ILED x # of LEDs (48EA) ). 6. End of Life shall be determined by the time when any of the following is satisfied under continuous lighting at 25 and ILED = 16.9mA. -. Intensity drops to 50% of the Initial Value (Luminance Spec.) -. Based on LED
3.2 PWM Duty Ratio vs Brightness
100 90 Relative Brightness (%) 80 70 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 90 100 Duty Ratio (%)
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 8 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
4.0 OPTICAL SPECIFICATIONS
4.1 Overview The test of optical specifications shall be measured in a dark room (ambient luminance 1 lux and temperature = 252) with the equipment of Luminance meter system (Goniometer system and TOPCON BM-5A) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of and equal to 0. We refer to O=0 (=3 ) as the 3 o'clock direction (the "right"), O=90 (= 12 ) as the 12 o'clock direction ("upward"), O=180 (= 9 ) as the 9 o'clock direction ("left") and O=270(= 6 ) as the 6 o'clock direction ("bottom"). While scanning and/or O, the center of the measuring spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to measurement. VDD shall be 3.3+/- 0.3V at 25C. Optimum viewing angle direction is 6 o'clock. 4.2 Optical Specifications Parameter
Viewing Angle Range Horizontal Vertical
Symbol
3 9 12 6 CR Yw Y5 Y13
Condition
CR > 10
Min.
500 250 80 60 0.273 0.289 0.540 0.333 0.304 0.525 0.109 0.097 3.0
Typ.
90 90 90 90 700 300 0.313 0.329 0.580 0.373 0.344 0.565 0.149 0.137 42 30 500 3.5
Max.
0.353 0.369 0.620 0.413 0.384 0.605 0.189 0.177
Unit Remarks
Deg. Deg. Deg. Deg. cd/m2 % Note 3 Note 1 Note 2
Luminance Contrast Ratio Luminance of 5 Points White 5 Points White Luminance 13 Points Uniformity White Red Green Blue Color Reproduction Response Time Cross Talk Brightness Outdoor Spec. Reflectance
Color Chromaticity
Wx Wy Rx Ry Gx Gy Bx By
Total (Tr + Td) CT Center Ri
= 0
Note 4
% 2.0 ms % ms % Note 5 Note 6 Note 7 Note 8
Ta= 25 C = 0 = 0 = 0
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 9 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
Note : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o'clock direction and the vertical or 6, 12 o'clock direction with respect to the optical axis which is normal to the LCD surface (see FIGURE 1 shown in page 11). 2. Contrast measurements shall be made at viewing angle of = 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in page 11) Luminance Contrast Ratio (CR) is defined mathematically. CR = Luminance when displaying a white raster Luminance when displaying a black raster
3. The White luminance uniformity on LCD surface is then expressed. (See FIGURE 2~3 shown in page 12) Uniformity Y = Minimum Luminance of 5(or 13) points Maximum Luminance of 5(or 13) points X 100 (%)
4. The color chromaticity coordinates specified in Table 4 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. 5. The electro-optical response time measurements shall be made as FIGURE 4 shown in page 13 by switching the "data" input signal OFF and ON. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Td. (See FIGURE 4 shown in page 13) 6. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark. (See FIGURE 5 shown in page 13) 7. Measure condition: Light source is 5,000nits, 15 degree position & BLU on (See FIGURE 1 shown in page 11) 8. Reference : Standard White Plate (BaSO4) Reflectance = Light intensity of the reflected light on LCD Module Output intensity of the reflected light on Reference x 100%
Measure condition: Light source is 5,000nits, 15 degree position & BLU off (See FIGURE 1 shown in page 11)
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 10 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT 4.3 Optical Measurements Figure 1. Measurement Set Up
REV P2
ISSUE DATE 2008. 01. 14
(L = 5 0 c m )
30
Detector
Light Source (Halogen Lamp)
50cm 15cm Module (BL on & off)
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 11 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
Figure 2. White Luminance and Uniformity Measurement Locations (5 points)
Column Row 200 320 640 960
400
600
Note. Luminance of white is defined as luminance values of 5 points across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in Figure 2 for a total of the measurements per display. * Yw = (Sum of 5 Points Luminance / 5 )
Figure 3. Uniformity Measurement Locations (13 points)
200
400
600
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 12 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
Figure 4. Response Time Testing
TFT Off(Black)
TFT On(White)
TFT Off(Black)
Tr
Td
100% 90% 10% 0%
Figure 5. Cross Modulation Test Description
VIEW AREA VIEW AREA 320,200 960,200
L31
320,600 960,600
YB(1120, 400)
YA (1120, 400) Cross-Talk (%) = Where: YB - Y A YB x 100
L0
YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location measured will be exactly the same in both patterns
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 13 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
5.0 INTERFACE CONNECTIONS
5.1 Electrical Interface Connection
CN1
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Interface Connector (FI-JH40S-HF10, Manufactured by JAE)
Symbol GND1 CONNTST LVDD1 LVDD2 LVDD3 VDD_DEID TEST CLK_EDID DATA_EDID GND2 GND3 NC RIN0RIN0+ GND4 RIN1RIN1+ GND5 RIN2RIN2+ GROUND Connector Test Logic Power Supply : +3.3V Logic Power Supply : +3.3V Logic Power Supply : +3.3V EDID Power Supply : +3.3V NON-CONNECTION EDID Clock EDID Data GROUND GROUND NON-CONNECTION LVDS Negative data signal (-) LVDS Positive data signal (+) GROUND LVDS Negative data signal (-) LVDS Positive data signal (+) GROUND LVDS Negative data signal (-) LVDS Positive data signal (+) Function Pin No. 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Symbol GND6 RCLKINRCLKIN+ GND7 VDIM Reserved Reserved HVGND1 HVGND2 HVGND3 HVGND4 HVGND5 NC HVDD1 HVDD2 HVDD3 HVDD4 HVDD5 CONNTST GND8 GROUND LVDS Negative clock signal (-) LVDS Positive clock signal (+) GROUND PWM Brightness Control NON-CONNECTION NON-CONNECTION GROUND GROUND GROUND GROUND GROUND NON-CONNECTION Back-light Power Supply: +12V Back-light Power Supply: +12V Back-light Power Supply: +12V Back-light Power Supply: +12V Back-light Power Supply: +12V Connector Test GROUND Function
Note 1. Connected with No. 2 & 39 Note 2. Start from left side
PCB
#1
#40
CN1 (FI-JH40S-HF10)
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 14 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT 5.2 LVDS Interface LVDS Transmitter : THC63LVDM83A
Input signal R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 HSYNC VSYNC DE MCLK Transmitter Pin No 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 27 28 30 31 40 39 CLKOUTCLKOUT+ CLKINCLKIN+ 42 41 OUT2OUT2+ IN2IN2+ 46 45 OUT1OUT1+ IN1IN1+ 48 47 OUT0OUT0+ IN0IN0+ Pin No Interface System (Tx) TFT-LCD (Rx)
REV P2
ISSUE DATE 2008. 01. 14
FI-JH40SHF10 Pin No.
Remark
13 14
16 17
19 20
22 23
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 15 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT 5.3 Back-light Interface
CN2 Pin No. 1 2 3 4 5 6 7 8 9
REV P2
ISSUE DATE 2008. 01. 14
LED FPC Connector (04-6298-009, Manufactured by Kyocera) Symbol Anode1 Anode2 Anode3 Anode4 NC Cathode1 Cathode2 Cathode3 Cathode4 Function LED Anode Power Supply LED Anode Power Supply LED Anode Power Supply LED Anode Power Supply Non-Connection LED Cathode Power Supply LED Cathode Power Supply LED Cathode Power Supply LED Cathode Power Supply LED Cathode Power Supply LED Anode Power Supply (3.25V X 12EA = 39V) Remark
5.4 Data Input Format
(1,1) (2,1) RGBRGB (1279,1)(1280,1) RGBRGB
1 Pixel = 3 Dots
RGB
RGBRGB (1,800) (2,800)
RGBRGB (1279,800)(1280,800)
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 16 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
6.0. SIGNAL TIMING SPECIFICATIONS
6.1 The 12.1" WXGA LCM is operated by the only DE (Data enable) mode (LVDS Transmitter Input) Item Frame Period Vertical Display Period One line Scanning Period Horizontal Display Period Clock Frequency Symbol T1 T2 T3 T4 1/T5 Min. 810 1350 Typ. 823 800 1440 1280 69.3 Max. Unit Lines Lines Clocks Clocks MHz
7.0 SIGNAL TIMING WAVEFORMS
7.1 Timing Waveforms of Interface Signal
T1 T2 DE T3 DCLK T5 T4 DE DATA SIGNALS
Valid display data (1280 Clocks)
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 17 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT 7.2 LVDS Rx Interface Timing Parameter The specification of the LVDS Rx interface timing parameter
< LVDS Rx Interface Timing Specification>
REV P2
ISSUE DATE 2008. 01. 14
Item CLKIN Period Input Data 0 Input Data 1 Input Data 2 Input Data 3 Input Data 4 Input Data 5 Input Data 6
Symbol tRCIP tRIP0 tRIP1 tRIP2 tRIP3 tRIP4 tRIP5 tRIP6
Min. 12.50 -0.4 tRICP/7-0.4
Typ. 14.43 0.0 tRICP/7
Max. 25.00 +0.4 tRICP/7+0.4
Unit Remarks nsec nsec nsec
2 xtRICP/7-0.4 2 xtRICP/7 2 xtRICP/7+0.4 nsec 3 xtRICP/7-0.4 3 xtRICP/7 3 xtRICP/7+0.4 nsec 4 xtRICP/7-0.4 4 xtRICP/7 4 xtRICP/7+0.4 nsec 5 xtRICP/7-0.4 5 xtRICP/7 5 xtRICP/7+0.4 nsec 6 xtRICP/7-0.4 6 xtRICP/7 6 xtRICP/7+0.4 nsec
tRIP6 tRIP5 tRIP4 tRIP3 tRIP2 tRIP1 tRIP0 RxINz +/* Z = 0, 1, 2 RxCLKIN+/Rx Rx Rx Rx Rx Rx Rx Rx Rx Rx Rx
Vdiff=0[v] tRCIP
Vdiff=0[v]
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 18 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS
Each color is displayed in sixty-four gray scales from a 6 bit data signal input. A total of 262,144 colors are derived from the resultant 18 bit data.
Colors & Gray Scale Black Blue Green Basic Cyan Colors Red Magenta Yellow White Black Darker Gray Scale Of Red Brighter Red Black Darker Gray Scale Of Green Brighter Green Black Darker Gray Scale Of Blue Brighter Blue Black Gray Darker Scale Of White & Brighter Black White Red Data
R5 R4 R3 R2 R1 R0 G5
Green Data 0 0 0 0 1 1 1 1 0 0 1 0 0 0 0 1 1 1 1 0 1 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0
Blue Data 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0
G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
0 0 0 0 1 1 1 1 0 0 0
0 0 0 0 1 1 1 1 0 0 0
0 0 0 0 1 1 1 1 0 0 0
0 0 0 0 1 1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 1 1 0 0 0
1 0 1 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 1 1 0 0 0
1 0 1 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 1
0 0 0 0 1 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 1 1 0 0 1
1 0 1 0 1 0
1 1 1
1 1 1
1 1 1
1 1 1
0 1 1
1 0 1
1 1 1
1 1 1
1 1 1
1 1 1
0 1 1
1 0 1
1 1 1
1 1 1
1 1 1
1 1 1
0 1 1
1 0 1
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 19 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
9.0 POWER SEQUENCE
To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below
0.9VDD
Power Supply
0V
0.9VDD 0.1VDD
0.1VDD
T1 T2
T5
T7 T6
Interface Signal
Valid
0V
T3
T4
Back- light
0V
T1 10 ms 0 T2 50 ms 200 ms T3 200 ms T4 0 T5 50 ms 0 T6 10ms 500ms T7 Notes : 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interface signal are valid.
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 20 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
10.0 MECHANICAL CHARACTERISTICS
10.1 Dimensional Requirements Figure 6 & 7 (located in 11.0) shows mechanical outlines for the model Parameter Active Area Number of pixels Pixel pitch Pixel arrangement Display colors Display mode Outline dimension Weight Back-light Specification 261.12(H) X 163.20(V) 1280(H) X 800(V) (1 pixel = R + G + B dots) 0.204(H) X 0.204(V) RGB Vertical stripe 262,144 Normally Black 276.80.3(H)x180.0(V)0.3x6.8(D:Max.) 265(Typ.) / 275(Max.) SMD LED (48EA) Array mm g Unit mm
10.2 Mounting See Figure 6 & 7 & 8. (shown in 11.0) Parameter Torque of side mounting screw Torque of ground plate screw Torque of top side screw 2.5(Max.) 1.5(Max.) 2.5(Max.) Specification Unit kgf kgf kgf
10.3 Anti-Glare and Polarizer Hardness. The surface of the LCD has an anti-glare coating to minimize reflection and a coating to reduce scratching. 10.4 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level of 150lux. The manufacture shall furnish limit samples of the panel showing the light leakage acceptable.
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 21 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
11.0 Mechanical Drawing
Figure 6. TFT-LCD Module Outline Dimension (Front View)
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 22 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
Figure 7. TFT-LCD Module Outline Dimensions (Rear view)
HX121WX1-100
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 23 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
Figure 8. TFT-LCD Module Section for Mounting
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 24 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
12.0 RELIABLITY TEST
The Reliability test items and its conditions are shown in below. No 1 2 3 4 5 6 7 Test Item High temperature storage test Low temperature storage test High temperature & high humidity operation test High temperature operation test Low temperature operation test Thermal shock Vibration test (non-operating) Shock test (non-operating) Electro-static discharge test (non-operating) Conditions
Ta = 60 C, 240 hrs Ta = -20 C, 240 hrs Ta = 50 , 80%RH, 240hrs Ta = 50 C, 240 hrs Ta = 0 C, 240 hrs Ta = -20 C 60 C (30 min), 100 cycle Frequency : 10~500Hz Gravity/AMP : 1.5G Period : X,Y,Z 30min Gravity : 220G Pulse width : 2ms, half sine wave X, Y, Z Once for each direction Air : 150pF, 330ohm, 15KV Contact : 150pF, 330ohm, 8KV
8
9
13.0 HANDLING & CAUTIONS
13.1 Cautions when taking out the module Pick the pouch only, when taking out module from a shipping package. 13.2 Cautions for handling the module As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. As the LCD panel and back - light element are made from fragile glass (epoxy) material, impulse and pressure to the LCD module should be avoided. As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. Do not pull the interface connector in or out while the LCD module is operating. Put the module display side down on a flat horizontal plane. Handle connectors and cables with care. SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 25 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
13.3 Cautions for the operation When the module is operating, do not lose MCLK, DE signals. If any one of these signals were lost, the LCD panel would be damaged. Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged. 13.4 Cautions for the atmosphere Dew drop atmosphere should be avoided. Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended. 13.5 Cautions for the module characteristics Do not apply fixed pattern data signal to the LCD module at product aging. Applying fixed pattern for a long time may cause image sticking. 13.6 Cautions for the digitizer assembly When assembling FPC connector, do not flip connector past 90 due to possible damage to connector. When positioning digitizer underneath driver IC, do not lift driver IC past 90 due to possible damage to drive IC pattern. Please be warned that during assembly of digitizer, the opening or closing of FPC will result in possible electrostatic discharge damage to the LED 13.7 Other cautions Do not re-adjust variable resistor or switch etc. When returning the module for repair or etc., Please pack the module not to be broken. We recommend to use the original shipping packages.
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 26 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
14.0 LABELS
14.1 Product Label
HX121WX1-100
BOE HYDIS Barcode
1 2 3 4 5 6 7
XX
X
X
XX
X
X XX
X
XXXXXX
No 1. Control Number No 2. Rank / Grade No 3. Line Classification (BOE HYDIS : H, LCM : L, BOE OT : A/B/C) No 4. Year (5 : 2005, 6 : 2006, ...)
No 5. Month (1, 2, 3,..., 9, X, Y, Z) No 6. FG Code No 7. Serial Number
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 27 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
14.2 Packing Label Label Size: 108 mm (L) x 56 mm (W) Contents Model: HX121WX1-100 Qty: Module Qty in one box Serial No.: Box Serial No. See next figure for detail description. Date: Packing Date FG Code: FG Code of Product
HX121WX1-100 * 0000000000000 *
10 200X.X.XX 1 0
XXXX
00 0 00 0 0 000000 Type Grade Year Month ITEM-CODE Serial_no
FG CODE
RoHS Mark
SPEC. NUMBER B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 28 OF 29 A4(210 X 297)
PRODUCT GROUP TFT LCD PRODUCT
REV P2
ISSUE DATE 2008. 01. 14
15.0 PACKING INFORMATION
15.1 Packing order
Put silica gels in the box.
Put Pad into the box.
After sealing the box, attach Packing Label on the attach position sign area of the box.
Place a cover on the top of the box. As shown in the figure, place the Modules bundled by shielding bag in the box.
15.2 Notes Box Dimension : 349.0mm(W) X 261.0mm(D) X 311.0mm(H) Package Quantity in one Box : 10pcs SPEC. NUMBER B2005-C001-A (3/3) SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE 29 OF 29 A4(210 X 297)
| |
Price & Availability of HX121WX1-100
 |
|
|
|
|
|
All Rights Reserved ©
IC-ON-LINE 2003 - 2022 |
.
.
.
.
.
| |
We use cookies to deliver the best possible
web experience and assist with our advertising efforts. By continuing to use
this site, you consent to the use of cookies. For more information on
cookies, please take a look at our
Privacy Policy. |
X |
|
